Ld gnu manual

[Rahnasto]

.
.
Download / Read Online Ld gnu manual >>
http://www.xsc.file1.site/download?file=ld+gnu+manual
.
.
.

<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
<br>
.
The linker command script includes a command specifically forspecifying a version script, and is only meaningful for ELF platformsthat support shared libraries. Not for children under 14 years. For subsequent flights, power ON the transmitter for 5 seconds before connecting the flight battery. All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury. Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury. Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury. This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury. Not for children under 14 years. Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control. Always keep all chemicals, small parts and anything electrical out of the reach of children. Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics. Never place any portion of the model in your mouth as it could cause serious injury or even death. Never operate your model with low transmitter batteries. Always keep aircraft in sight and under control. Always use fully charged batteries. Always keep the transmitter powered on while aircraft is powered. Always remove batteries before disassembly. Always let parts cool after use before touching. Always remove batteries after use. Always ensure failsafe is properly set before flying. Never operate aircraft with damaged wiring. Perform a radio system Range Check. Plan flight for flying field conditions. Perform Control Direction Test with transmitter. Set flight timer for 5 minutes for first flight. Perform AS3X Control Direction Test with aircraft. After you set up your model, alwaysrebind the transmitter and receiver to set the desired fa ilsafe positions. Always engage throttle cut before approaching the aircraft. Low rate is recommended for the initial flights. If oscillation occurs at high speed, refer to the Troubleshooting Guide for more information. After your initial flights, you may adjust the expo value to better suit your flying style. Make sure the flight battery is disconnected from the aircraft. Place the aircraft on a level surface away from wind. Connect the flight battery in the aircraft. Make sure the transmitter controls are neutral and the throttle and throttle trim are in low position. Put your transmitter into bind mode. After 5 to 10 seconds, the receiver status LED will turn solid, indicating that the receiver is bound to the transmitter. If the LED does not turn solid, refer to the Troubleshooting Guide at the back of the manual. Begin with the transmitter bound to the receiver. A signal bar appears in the top left corner of the screen when the telemetry information is being received. Scroll past the servo monitor to view the technology screens. For more information about compatible transmitters, firmware updates, and how to use the telemetry technology on your transmitter, visit Always keep material or debris away from the intake. When armed, the rotor will turn in response to throttle movement and could ingest loose objects. It is important to only use a small piece to prevent the battery from shifting. Using too large of a piece will make it difficult to remove the battery and may lead to fuselage damage. Lower the throttle and throttle trim to the lowest settings on your transmitter. Adjust as needed by sliding the battery forward or back. Power ON your Transmitter, then wait 5 seconds. Connect the battery to the ESC, noting proper polarity. Keep the plane immobile and away filexlib.
.
Ld gnu podrecznik <br> Ld gnu user manual<br>Ld gnu guide <br> Ld gnu owner guide<br>Ld gnu handbog